AirTouch™ Help Videos


The following short videos have been created to help you with every aspect of your AirTouch™ Mask.
If you require further information, email us at mysleep@resmed.co.uk or call us on 0800 917 7071 and one of the mySleep team will be happy to assist you.

1. The AirTouch F20: The Softest CPAP Mask from ResMed

With ResMed’s new UltraSoft™ memory foam, the AirTouch F20 full face mask adapts to the contours of each patient’s face, creating a personalized fit for the ultimate experience in cushion comfort.

2. How to fit your AirTouch F20 full face mask

  1. Unclip the magnetic clips.
  2. With the mask held against your face, pull the headgear over your head. Ensure the top of the mask cushion is sitting comfortably at the top of your nasal bridge. The bottom of your headgear should settle comfortably at the top of your neck – with the top of the headgear sitting at the top of your crown.
  3. Bring each of the magnets up to meet their corresponding clips on the frame.
  4. Adjust the tabs on the upper headgear.
  5. Adjust the tabs on the lower headgear.
  6. With your device still switched off, connect your device tubing to your mask elbow.
  7. Connect the elbow to your mask.

To prepare your mask for therapy:

  1. Switch on your device and position yourself as if you are to begin therapy (e.g. lying down in bed).
  2. Adjust your upper straps.
  3. Adjust your lower straps.
  4. Practice reseating your cushion – turn off your device, pull your mask away from your face, allow your cushion to reassume its natural shape and then resettle your cushion on your face, with the top of the cushion sitting at the top of your nasal bridge.

These instructions are for general information purpose only. For full details, consult the user guide.

3. How to disassemble your AirTouch F20 full face mask

  1. Remove elbow from frame.
  2. Unclip the magnetic clips.
  3. Undo upper headgear tabs.
  4. Pull strapping away from frame.
  5. Pull cushion away from frame.

4. How to clean your AirTouch F20 full face mask daily

  1. Disassemble mask.
  2. If necessary, wipe down the cushion with dry or non-alcoholic wipes only. Do not get the cushion wet.
  3. Rinse frame and elbow under running water. Clean each component with a soft bristle brush.
  4. Soak components in warm water with mild liquid detergent for up to 10 minutes.
  5. Shake components in water.
  6. Brush moving parts of elbow and around vent holes.
  7. Brush areas of frame where arms connect, and inside and outside the frame where the elbow connects.
  8. Rinse components under running water.
  9. Leave components to air dry out of direct sunlight – making sure to squeeze the arms of the frame to ensure excess water is removed.

5. How to assemble your AirTouch F20 full face mask

  1. Attach cushion to frame.
  2. Attach the magnetic clips.
  3. Connect upper headgear straps.
  4. Connect elbow to mask frame.

These instructions are for general information purpose only. For full details, consult the user guide.

6. How to clean your AirTouch F20 full face mask weekly

  1.  Disassemble mask. The magnetic clips can remain attached to headgear during cleaning.
  2. Handwash headgear in warm water with mild liquid detergent.
  3. Rinse headgear under running water. Inspect to ensure headgear is clean and detergent-free. Wash and rinse again, if necessary.
  4. Squeeze headgear to remove excess water.
  5. Leave headgear to air dry out of direct sunlight.

7. Hair management tips for the AirTouch F20 for Her full face mask

Here are a few tips for how to manage your hair when wearing the AirTouch F20 for Her full face mask.

8. How to change the cushion on your AirTouch F20 full face mask

Watch this step by step guide on how to change the memory foam cushion on your AirTouch F20 full face mask.